Janazzo Services

In Pursuit Of Excellence
  • Toll Free: 800-297-3931
  • Phone: 860-621-7381
  • Service: 860-621-8974
  • Fax: 860-621-7529


Home Services












    • The Janazzo Advantage

    JANAZZO PEACE OF MIND
    The plans are designed to extend the life of your heating or cooling units, and help cut costly repairs. The type of equipment maintenance we offer is industry recognized as the best way to maximize your energy efficiency. The plans also promote a safer environment for your family, by performing safety checks that guard against deadly carbon monoxide leaks.



    SERVICE YOU CAN TRUST
    Our highly skilled and licensed technicians will provide to you the best home-care possible. You can rely on the professionals at JANAZZO to give you fast, dependable superior service.



    10% PREFERRED GMA CUSTOMER DISCOUNT
    The preferred customer status over a non-agreement customer entitles the GMA customer to a 10% discount off the repair of any equipment covered by this agreement.



    TWO-YEAR GMA WARRANTY
    Two-year parts and labor warranty on most repairs as long as this agreement is in effect.



    24-HOUR EMERGENCY SERVICE
    After hour emergency service is available at our after hour rate.



    AUTOMATIC RENEWAL
    Yearly renewals will be sent for your approval.



     
     





    PLAN A, P, X
    (Standard Gas Furnace)
    (Pulse & Condensing Type)
    (Complete Heat)
    • Check automatic controls
    • Clean burners as needed
    • Check and clean heat exchanger as needed
    • Inspect for combustion leaks
    • Test flue for satisfactory operation
    • Check for proper fuel consumption
    • Check manifold gas pressure
    • Check temperature rise per manufacturer's specification
    • Check CO2, O2,and test for Carbon Monoxide
    • Adjust combustion for optimum efficiency
    • Lubricate moving parts as needed
    • Test safety and operating controls
    • Lubricate motors and bearings as required
    • Check belt wear, tension and alignment (if applicable)
    • Inspect air blower wheel
    • Replace disposable air filters
    • Check flame signal readings
    • Check thermostat operation
    • Record detailed information on log sheet




    PLAN AH
    (Air Handler)
    • Check fins and clean coil
    • Check electrical connections for tightness
    • Check blower belt wear,tension and alignment
    • Inspect air blower wheel
    • Lubricate motors and moving parts as required
    • Check voltage and amperage readings
    • Replace disposable air filters
    • Check thermostat operation
    • Record detailed information on log sheet




    Plan AP
    (Air Purifier)
    • Check power to unit
    • Check electrical connections
    • Check airflow switch
    • Check voltage readings
    • Annual maintenance kit (filter, metal insert and UV lights)
    • Record detailed information on log sheet




    Plan B
    (Oil Furnace)
    • Clean and adjust electrodes
    • Clean and inspect burner tube,burner blower wheel,
      cad cell,fuel pump strainer, and primary air band
    • Replace fuel oil nozzle and fuel oil filter cartridge
    • Lubricate burner motor, inspect combustion chamber
      operating controls, safety controls, and breaching
    • Clean fuel passageways(heat exchanger section) and breaching
    • Inspect blower for proper operation
    • Check belt wear, tension and alignment (if applicable)
    • Lubricate blower motor and bearings as required
    • Replace disposable air filters
    • Check draft over fire and breaching
    • Check CO2, O2, Smoke and Carbon Monoxide
    • Adjust System for optimum efficiency
    • Check temperature rise per manufacturer's specification
    • Check thermostat operation
    • Record detailed information on log sheets




    Plan C
    (Air Conditioner)
    • Check fins and clean condensor coil
    • Check electrical connections for tightness
    • Visually check for oil and refrigerant leaks
    • Check blower belt wear, tension and alignment (if applicable)
    • Replace disposable air filters
    • Check and clean condensate drain
    • Inspect air blower wheel
    • Lubricate motors and moving parts as required
    • Check refrigerant operation pressures
    • Check sub-cooling and superheat readings
    • Check temperature drop across evaporator coil
    • Check voltage and amperage readings
    • Check thermostat operation
    • Record detailed information on log sheet




    Plan D
    (Heat Pump)
    • Lubricate motors and moving parts as needed
    • Check defrost cycle and reversing valve operation
    • Inspect air blower wheel
    • Check blower belt wear, tension and alignment
    • Visually check for oil and refrigerant leaks
    • Check electrical controls and crankcase heater
    • Replace disposable air filters
    • Check and clean condensate drain
    • Check and tighten electrical connections
    • Check voltage and and amperage readings
    • Check operating pressures and temperatures
    • Check auxillary heat for proper operation
    • Check temperature across air handler
    • Check Thermostat operation
    • Record detailed information on log sheet




    Plan E
    (Electric Furnace)
    • Check operation of controls
    • Check all wiring for loose connections and condition of insulation
    • Check voltage supply and amperage readings
    • Lubricate blower motor and moving parts as required
    • Inspect blower wheel
    • Check belt wear, tension and alignment (if applicable)
    • Replace disposable air filters
    • Check blower operation and staging of heating elements
    • Check thermostat operation
    • Record detailed information on log sheet




    Plan EAC
    (Electric Air Cleaner)
    • Check power to unit
    • Check electrical connections
    • Check airflow switch
    • Check voltage readings
    • Remove and clean electronic cells and pre-filters
    • Record detailed information on log sheet




    Plan G
    (Gas Boiler)
    • Check automatic controls
    • Clean burners as needed
    • Check and clean heat exchanger as needed
    • Inspect for combustion leaks
    • Test flue for satisfactory operation
    • Lubricate moving parts as required
    • Check for proper fuel consumption
    • Check manifold gas pressure
    • Check CO2, O2, Smoke and Carbon Monoxide
    • Adjust combustion for optimum efficiency
    • Test safety and operation controls
    • Check voltage and amperage readings
    • Check flame signal readings
    • Chek thermostat operation
    • Check circulator and zone valve operation
    • Record detailed information on log sheet




    Plan GEN
    (Generator)
    • Check automatic controls
    • Check electrical connections for tightness
    • Replace spark plugs
    • Replace crankcase oil
    • Replace oil filter
    • Lubricate moving parts as needed
    • Check and clean battery leads
    • Check operation of battery charger
    • Replace air filter
    • Check voltage and amperage readings
    • Check manifold pressure readings and input
    • Check operating and safety controls
    • Visually check for leaks
    • Record detailed information on log sheet




    Plan HUM
    (Humidifier)
    • Clean drain pan (replace if disposable type)
    • Clean and adjust float assembly
    • Remove and replace pad
    • Check motor operation (if applicable)
    • Check heating elements (if applicable)
    • Check operating and safety controls
    • Check drain (if applicable)
    • Check voltage and amperage readings
    • Check humidistat setting and operation
    • Record detailed information on log sheet




    Plan HWE
    (Electric Hot Water Heater)
    • Check condition of insulation on wiring
    • Check electrical connections for tightness
    • Check voltage and amperage readings
    • Check operation of heating elements
    • Check operating and safety controls
    • Record detailed information on log sheet




    Plan HWG
    (Gas Hot Water Heater)
    • Check automatic controls
    • Clean burners as needed
    • Check and clean heat exchangers as needed
    • Inspect for combustion leaks
    • Test flue for satisfactory operation
    • Lubricate moving parts as required
    • Check for proper fuel consumption
    • Check manifold gas pressure
    • Check CO2,O2, and test for Carbon Monoxide
    • Adjust combustion for optimum efficiency
    • Test safety and operating controls
    • Check voltage and amperage readings
    • Check flame signal readings
    • Check thermostat operation
    • Record detailed information on log sheet




    Plan HWO
    (Oil Water Heater)
    • Clean and adjust electrodes,burner blower wheel,
      cad cell,fuel pump strainer, and primary air band
    • Replace fuel oil nozzle and fuel oil filter cartridge
    • Lubricate burner motor, inspect combustion chamber, operating
      controls and safety controls
    • Clean flue passageways and breaching
    • Check draft over fire and breaching
    • Check CO2,O2, Smoke and Carbon Monoxide
    • Adjust system for optimum efficiency
    • Lubricate motors and moving parts as required
    • Check circulator if applicable
    • Check voltage and amperage readings
    • Check thermostat operation
    • Record detailed information on log sheet




    Plan O
    (Oil Boiler)
    • Clean and adjust electrodes, burner blower wheel,
      cad cell,fuel pump strainer, and primary air band
    • Replace fuel oil nozzle and fuel oil filter cartridge
    • Lubricate burner motor, inspect combustion chamber, operating
      controls and safety controls
    • Clean flue passageways (boiler sections and breaching)
    • Inspect and lubricate circulator, drain expansion tank as necessary
    • Check draft over fire and breaching
    • Check CO2,O2, Smoke and Carbon Monoxide
    • Adjust system for optimum efficiency
    • Lubricate motors and moving parts as required
    • Check circulator and zone valve operation
    • Check voltage and amperage readings
    • Check thermostat operation
    • Record detailed information on log sheet
    X